Acid, laser, plasma, and mechanical decapsulation each protect different things and put different things at risk. This guide compares the four methods by speed, copper and silver wire safety, evidence preservation, and package type, and explains how to extract an intact, functional die.

Almost every die-level failure analysis starts the same way: the package has to come off before anything else can happen. Photon emission, laser-based fault isolation, thermal mapping, delayering, FIB work, and even a simple high-magnification optical inspection all require clean, controlled access to the die. Decapsulation is the step that provides that access, and it is also the step where a good analysis is most easily lost.

A decap that corrodes the bond pads, dissolves a copper wire, cracks the die, or washes away the corrosion residue that caused the failure cannot be undone. The four families of methods used today, acid (wet chemical) decapsulation, laser ablation, plasma (reactive ion etch) decapsulation, and mechanical decapsulation, each solve a different part of that problem. This article compares them the way we compare them at the bench: by what they preserve, what they put at risk, how fast they work, and which package and interconnect combinations they suit. It closes with die extraction, where the goal is not just to expose the die but to remove it intact and functional.

Who This Article Is For

FA, reliability, quality, and component engineers who order or perform decapsulation, program managers evaluating counterfeit or DPA results, and IP attorneys who need a die exposed for evidence of use work. The focus is on choosing the method, not on operating a specific instrument.

Define the Goal Before Choosing the Method

The most common decapsulation mistake is choosing the method before deciding what the decap must deliver. The same package can be opened four different ways, and the right one depends on what happens next. Before any material is removed, answer five questions:

  • Must the device remain electrically functional? Fault isolation on a powered device needs intact wires, bond pads, and lead frame connections. A decap for optical inspection or die marking verification does not.
  • What is the interconnect metallurgy? Gold, copper, palladium-coated copper, silver alloy, and aluminum wedge wire, flip-chip bumps, and copper pillars all respond differently to acids and plasmas. Copper and silver are the most vulnerable.
  • Is there evidence on or near the die surface that must survive? Corrosion products, ionic contamination, foreign material, and delamination paths are often the root cause. An aggressive wet decap can remove them before anyone sees them.
  • How much of the die needs to be exposed? A small window over a known site, the full die surface with bond wires, the die backside, or the whole die freed from the package for extraction.
  • What is the package construction? Plastic mold compound, ceramic cavity, metal can, stacked-die or system-in-package, or a module with multiple components and an over-mold.

The answers usually narrow the choice to one primary method, often combined with a second method for the final approach. Treat the decap as a plan, not a recipe.

Non-Destructive Work Comes First

Decapsulation is destructive, so every question that can be answered non-destructively should be answered before the package is opened. A typical pre-decap sequence in our lab includes:

  • External visual inspection and photo documentation of the markings, package surfaces, leads, and any visible damage. For counterfeit and evidence of use work, this record is part of the deliverable.
  • X-ray inspection to map the die position, die size, wire layout, wire loop heights, die attach, and lead frame. Loop height and die depth set the safe removal depth for laser and mechanical methods.
  • Scanning acoustic microscopy to locate delamination at the die surface, paddle, and lead frame interfaces. Delamination found after a wet decap is uninterpretable, because the acid itself travels along and enlarges delaminated interfaces.
  • Electrical characterization of the failure, so the same measurement can be repeated after the decap to confirm the failure mode survived.
Practical Tip: Re-Test After Decap

Measure the failing signature before decapsulation and again immediately after. If a leakage path or open disappears after the decap, the failure may have been in the package (moisture, ionic contamination, a cracked wire or a delaminated interface) rather than on the die, and that is a finding in itself.


Acid (Wet Chemical) Decapsulation

Wet chemical decapsulation remains the fastest and most widely used method for plastic-encapsulated microcircuits. Heated acid is delivered to a defined window on the package surface, typically by an automated jet etcher that recirculates a controlled volume of acid through a gasket and mask, or by careful manual application for small or unusual parts. The acid attacks the organic resin in the mold compound, the freed silica filler is rinsed away, and the process is repeated in short cycles until the die and wires are exposed.

Technique SnapshotAcid Decapsulation
Best For
Plastic packages with Au wire; fast access to the full die surface
Typical Time
Minutes per part once the recipe is established
Selectivity
Area defined by mask and gasket; depth controlled by cycle count
Main Risks
Cu/Ag wire and bond pad attack; removal of corrosion evidence

Choosing the Chemistry

Mold compounds are not all the same. Epoxy novolac, biphenyl, and multi-aromatic resins, anhydride-cured systems, and the halogen-free "green" compounds that replaced brominated formulations all etch at different rates in different acids. The three chemistries we use cover nearly every plastic package:

Chemistry

Typical Use

Strengths

Watch Out For

Fuming nitric acid

Most epoxy mold compounds; gold wire bonds

Fast, clean, and selective to aluminum pads and gold wire at moderate temperature

Aggressive toward copper and silver wire; residual water accelerates metal attack

Fuming sulfuric acid

Hard-to-etch, highly cross-linked, and some anhydride-cured compounds

Attacks resins that nitric acid struggles with; higher operating temperature

Charring and residue; heavier attack on aluminum; slower rinse

Mixed acid (nitric/sulfuric blends)

Green compounds; copper and silver wire; balancing rate against metal attack

Ratio and temperature tuned per package; can passivate copper surfaces while still etching resin

Recipe development per mold compound and wire type; ratio drift with acid age

Table 1. Acid chemistries for plastic package decapsulation. Exact ratios and temperatures are set per package after a trial on a sacrificial part whenever one is available.

Copper and Silver Wire Bonds

Copper wire is now standard across consumer and much of automotive and industrial production, and silver alloy wire is common in LED and some discrete packages. Both dissolve in hot nitric acid far faster than gold. A recipe that works perfectly on a gold-wire part will leave a copper-wire part with thinned necks, missing wires, or an intact-looking wire that has lost its bond to the pad.

Preserving copper and silver wire with wet chemistry is a matter of controlling every variable at once: anhydrous, fresh acid, a mixed-acid ratio chosen to slow metal attack, lower temperature, shorter cycles with more frequent inspection, and a non-aqueous rinse so that diluted acid never sits on the metal. Water is the enemy here; dilute nitric acid attacks copper much faster than concentrated fuming acid. When the wire and pad must be evaluated for corrosion or intermetallic quality, plasma decapsulation or a laser-plus-plasma sequence is often the safer route.

Where Acid Decap Falls Short

Acid is not a neutral observer. It dissolves and rinses away chloride, sulfur, and other ionic residues, along with the corrosion products they created, so a corrosion failure decapsulated in acid may arrive at the SEM with no evidence of its own cause. Acid also wicks along delaminated interfaces and attacks the lead frame, die paddle, and bond pads beneath them. For corrosion, contamination, and moisture-related failures, plan the decap around preserving that evidence, and correlate with acoustic microscopy and FTIR or EDX of any residues before wet chemistry is used.

Laser Ablation Decapsulation

Laser decapsulation removes mold compound by scanning a pulsed laser over a defined area. The resin absorbs the laser energy and is ablated, and the silica filler is ejected with it. Because the pattern and depth are set by software, laser ablation is the most geometrically precise way to remove bulk mold compound: a rectangular window, a window shaped around the wire layout, or a stepped cavity that stops at different depths over the die and over the wire loops.

Technique SnapshotLaser Ablation
Best For
Fast, precise bulk removal; Cu/Ag wire packages; site-specific windows
Typical Time
Minutes for bulk removal, followed by a short chemical or plasma finish
Selectivity
Excellent lateral control; depth controlled by pass count and X-ray data
Main Risks
Thermal damage to wires and die surface if the laser reaches them

The key limitation is that the laser does not know when to stop. Mold compound, gold, copper, and silicon all absorb laser energy, so a laser that reaches the wire loops will cut, melt, or discolor them, and one that reaches the die can damage passivation and metallization. For that reason laser ablation is almost always used as a bulk removal step: X-ray data sets a stop depth above the highest wire loop, the laser removes the bulk of the compound in minutes, and a brief acid or plasma etch clears the remaining thin layer over the wires and die.

This combination is one of the most effective approaches for copper and silver wire packages. The acid exposure time drops from the full thickness of the package to a few tens of micrometers of compound, which reduces wire attack dramatically. Laser ablation is also well suited to thin packages, packages where only part of the die must be exposed, and modules where neighboring components must be left untouched.

Plasma (Reactive Ion Etch) Decapsulation

Plasma decapsulation removes mold compound with a reactive gas plasma rather than a liquid. An oxygen-based plasma oxidizes the organic resin to volatile products; a fluorine-bearing gas is added, or applied in alternating steps, to attack the silica filler that oxygen alone leaves behind. Process gases, flow, pressure, RF power, and time are tuned to the mold compound and package. A mask defines the area to be opened.

Technique SnapshotPlasma / RIE Decapsulation
Best For
Cu/Ag wire, corrosion and contamination evidence, sensitive die surfaces
Typical Time
Hours to days, depending on compound thickness and filler content
Selectivity
Highly selective to metals; no liquid to wick along interfaces
Main Risks
Slow throughput; fluorine chemistry attacks exposed passivation and glass

The advantage of plasma is that it is the gentlest of the four methods toward metals. Oxygen plasma does not dissolve copper, silver, gold, or aluminum wire, and there is no liquid to travel along delaminated interfaces or to dissolve ionic residues. A wire that was corroded before the decap is still corroded after it, and the residue is still there for EDX analysis. That makes plasma the method of choice for copper and silver wire bond evaluation, corrosion and contamination failures, and any decap where the analysis must show the die and interconnects exactly as they existed in the package.

The price is time. Plasma etches mold compound slowly, and the high filler content of modern compounds slows it further, because filler must be removed or rinsed off periodically to keep the resin exposed. Plasma is therefore most efficient as the final step after the bulk has been removed by laser or by mechanical thinning. The fluorine component must also be managed carefully near the end point, because it will etch silicon nitride and oxide passivation, glass, and any exposed silicon once the compound is gone.

When Evidence Matters More Than Speed

For corrosion, contamination, and moisture-related failures, and for litigation work where the condition of the die and wires is itself the evidence, a slower plasma decap is often the only method that preserves what the analysis needs to show. The extra day is usually far cheaper than an inconclusive result.

Mechanical Decapsulation and Delidding

Mechanical methods cover two quite different jobs. The first is opening hermetic packages: ceramic cavity packages, metal cans, and lidded hybrids and modules, where there is no mold compound to dissolve and the die sits in a sealed cavity. The second is mechanical thinning of plastic packages, using controlled grinding or milling to remove bulk material before a chemical or plasma finish, or to reach the die backside.

Technique SnapshotMechanical Decapsulation
Best For
Ceramic, metal can, and lidded hermetic packages; bulk thinning and backside access
Typical Time
Minutes to a few hours, depending on lid seal and package
Selectivity
Set by fixturing and X-ray-referenced depth
Main Risks
Particles in the cavity, die and wire damage from force, loss of cavity evidence

Opening Hermetic Packages

The technique depends on how the lid is sealed. Lids attached with solder or glass frit can sometimes be removed by grinding the seal or lid edge and lifting the lid. Seam-welded and brazed lids are typically ground or cut around the perimeter until the lid separates, and metal cans are opened by grinding through the can wall just below the weld or by cutting the cap away. In every case the goal is the same: open the cavity without allowing grinding debris, lid fragments, or seal glass to fall onto the die and wires, and without applying force that cracks the die or deforms the wires.

The cavity itself is often part of the evidence. Loose particles, foreign material, condensation residue, and wire sweep or contact are all findings that internal visual inspection must capture, so the cavity should be photographed immediately after the lid is removed, before any cleaning. If the analysis requires an internal gas measurement, it must be performed before the package is opened. For space and defense programs, delidding is typically followed by internal visual inspection to the applicable military test method criteria as part of destructive physical analysis.

Mechanical Thinning of Plastic Packages

For plastic packages, controlled grinding or milling is a useful way to remove bulk compound quickly without any chemistry, either over the die top or from the backside. As with laser ablation, X-ray measurements of die depth and wire loop height set a safe stop height. Mechanical thinning followed by plasma is a particularly gentle sequence for copper wire and corrosion work. Mechanical backside preparation is also the starting point for backside fault isolation, where the die must be thinned and polished rather than simply exposed.


Side-by-Side Comparison

The table below summarizes how the four methods compare on the criteria that usually drive the decision. Ratings are relative and assume a well-developed process for each method.

Criterion

Acid

Laser

Plasma / RIE

Mechanical

Speed

Fast

Fastest for bulk removal

Slow

Fast to moderate

Package types

Plastic

Plastic and over-molded modules

Plastic

Ceramic, metal, lidded; plastic thinning

Au wire safety

High

High until wires are reached

High

Moderate (mechanical force)

Cu / Ag wire safety

Moderate with tuned recipes

High until wires are reached

Highest

Moderate (mechanical force)

Preserves corrosion and ionic evidence

Low

High for bulk removal

Highest

High

Lateral precision

Good (mask and gasket)

Excellent

Good (mask)

Depends on fixturing

Functional device afterward

Yes, with correct recipe

Yes, with a chemical or plasma finish

Yes

Yes, with care

Typical role

Primary method for most plastic parts

Bulk removal before a short finish

Final approach; evidence-critical work

Hermetic delid; bulk or backside thinning

Table 2. Relative comparison of IC decapsulation methods.

Combined Sequences We Use Most Often

In practice, the best decap is frequently a sequence rather than a single method. Each step removes the material it handles best and hands off before it reaches the structures it would damage:

  • Laser + acid: laser removes bulk compound to a stop height above the wire loops; a short mixed-acid etch clears the remainder. Fast and reliable for most copper wire packages.
  • Laser or mechanical + plasma: bulk removal followed by a plasma finish. The gentlest sequence for corrosion, contamination, and copper or silver wire evaluation.
  • Acid + plasma: acid opens most of the window; plasma clears the final layer over sensitive pads or structures.
  • Mechanical delid + local cleaning: for hermetic packages, opening followed by inspection, documentation, and cleaning only where the analysis requires it.

Package- and Application-Specific Considerations

Flip-Chip and Backside Access

Flip-chip devices present the die backside, not the active surface, to the package top. Front-side decap is generally not an option without destroying the bumps, so these devices are approached from the backside: removal of the lid or mold, followed by thinning and polishing of the silicon for backside photon emission, laser-based fault isolation, or thermal work. The decision is less about which decap method and more about how far to thin the die.

Stacked Die, System-in-Package, and Modules

Multi-die packages require a layer-by-layer approach. X-ray and acoustic data define which die must be reached, and laser or mechanical removal opens the package to that level before a chemical or plasma finish. Wire bonds from upper die often loop over lower die, so the stop height is set by the highest wire over the target, not by the target die itself.

Counterfeit Detection

For counterfeit and suspect-part screening, the decap exists to verify die markings, die manufacturer, die revision, and bond layout against a known-good reference, so a clean, fully exposed die surface matters more than electrical function. Acid decapsulation is usually the efficient choice, with laser or plasma for copper wire parts where wire condition is part of the evaluation. Document the external markings and package features before the decap, because they are often the most important evidence.

Patent Evidence of Use

When a die is being examined to show whether a product practices a patent claim, the decap is part of a documented chain of evidence. The method should be chosen to preserve the structures that the claims describe, every step should be photographed and recorded, and the sample identity should be traceable from the as-received product to the final images. A controlled, recorded decap is easier to defend than a fast one.

Die Extraction: Removing an Intact, Functional Die

Die extraction goes one step further than decapsulation. Instead of exposing the die in place, the goal is to remove it entirely from the package, intact and, in many cases, still functional. It is used when:

  • A die must be re-assembled into a different package or onto a substrate, for example to recover an obsolete part, to build engineering samples, or to move a die into a package suited to a specific test or fixture.
  • Die-level testing or probing is needed without package parasitics or lead frame constraints.
  • Backside or full-die analysis is required, such as backside inspection, die thickness and die attach evaluation, or delayering of the full die.
  • Counterfeit or evidence of use work requires the complete die for imaging, measurement, or comparison.

How Extraction Differs From Decapsulation

A standard decap stops when the die surface is exposed and leaves the die attached to the paddle. Extraction must also remove the compound around the die edges and beneath it, separate the die from the die attach material, and remove the bond wires without damaging the bond pads. Each of those steps has its own risk:

  • Die attach removal. Epoxy die attach can be softened or removed chemically, while solder and sintered die attach often require thermal or mechanical separation. Excessive force or thermal shock cracks thin die.
  • Wire removal and pad condition. If the die is going to be re-bonded, the bond pads must be left in a bondable condition. Ball bond remnants, intermetallic, and acid-attacked aluminum all affect re-bond yield, so the decap chemistry and wire removal method are chosen with the re-assembly process in mind.
  • Handling and ESD. A bare die has no package to protect it. Extracted die are handled with ESD-safe tools, cleaned with compatible solvents, and stored in clean, ESD-protective carriers.
  • Functional verification. When function matters, the device is characterized before extraction and the die is tested again after re-assembly or probing, so any change can be attributed correctly.

Extraction is where the method comparison above matters most. A die destined for re-assembly needs clean, uncorroded aluminum pads, an undamaged passivation, and no cracks at the edges or corners, so the sequence is usually a combination of laser or mechanical bulk removal with a carefully controlled chemical or plasma finish.

Plan Extraction With the End Use in Mind

Before extraction begins, agree on what the die must be ready for: imaging only, probing, or re-bonding. Each end use sets different requirements for pad condition, cleanliness, and backside finish, and those requirements drive the method choice from the very first step.


Recognizing Decapsulation Artifacts

Like any preparation step, decapsulation can create features that look like failures. Before a finding goes into a report, confirm that it existed before the decap. The artifacts below are the ones we see most often.

Artifact

Can Be Mistaken For

Usual Cause

Prevention and Check

Bond pad corrosion or pitting

Field corrosion; manufacturing defect

Over-etch, wet acid, water in rinse

Fresh anhydrous acid; non-aqueous rinse; plasma finish for evidence-critical work

Thinned or missing Cu/Ag wire

Wire fusing, corrosion, or bonding defect

Hot nitric acid or diluted acid on copper or silver

Mixed-acid recipe; laser or plasma; compare with pre-decap X-ray

Lifted or cracked ball bond

Bond failure; cratering

Mechanical force, thermal shock, acid undercutting the pad

Pre-decap pull or electrical data; gentle handling; cross-section to confirm

Die crack or chipped edge

Handling or assembly damage

Mechanical delid force; thermal shock during extraction

Acoustic and X-ray before decap; controlled force and temperature

Burned or discolored compound and wires

Overstress or heat damage

Laser reaching wires or die

X-ray-referenced stop height; chemical or plasma finish

Residue or filler on die surface

Foreign material contamination

Incomplete rinse; plasma filler residue; charred sulfuric residue

Thorough rinse; periodic filler removal; EDX/FTIR of residue before conclusions

Passivation damage

Process defect; ESD or EOS damage

Fluorine plasma or acid over-etch at end point

Endpoint control; compare with an unexposed region of the die

Table 3. Common decapsulation artifacts and how to separate them from real failures.

A Decision Workflow for Choosing the Method

The workflow below summarizes how we move from a failure description to a decap plan.

01

Define the Goal

Functional device, optical inspection, evidence preservation, backside access, or full die extraction.

02

Characterize Non-Destructively

External visual, X-ray, acoustic microscopy, and electrical measurement of the failure.

03

Identify Package and Metallurgy

Plastic, ceramic, or metal; Au, Cu, Ag, or Al wire; wire bond or flip-chip; single die or stacked.

04

Select the Sequence

Acid, laser, plasma, or mechanical as the primary method, plus a finishing method where needed.

05

Decap and Verify

Expose the die in controlled steps, inspect frequently, and re-test the device electrically.

06

Document and Hand Off

Photograph as-exposed condition, then proceed to fault isolation, SEM/EDX, delayering, or extraction.

How Watson Analytical Applies These Techniques

All four decapsulation methods, acid, laser, plasma, and mechanical, are performed in-house at our San Diego laboratory, so the method is chosen for the device rather than for the equipment that happens to be available. Our package decapsulation work uses fuming nitric, fuming sulfuric, and mixed-acid chemistries, with recipes tuned for copper and silver wire bonds, alongside laser ablation, plasma decapsulation, and mechanical delidding of ceramic and metal packages.

Each decap is planned from X-ray inspection and scanning acoustic microscopy data, and the exposed die moves directly to semiconductor fault isolation, SEM/EDX analysis, IC delayering, FIB analysis, or cross-sectioning in the same lab. For flip-chip and backside work, we provide area defined backside preparation and die thinning.

We support semiconductor, defense, space, biomedical, and litigation customers, including counterfeit screening, portions of destructive physical analysis to MIL-STD-1580, die extraction, and patent evidence of use investigations where a documented decap is part of the evidence. Work is performed under our ISO 9001:2015 quality system, and ITAR-controlled devices are handled under our ITAR registration. Typical turnaround for package decapsulation is 2 to 3 days.

Not sure which decap method your device needs? Send us the part number, package type, and failure description, and we will recommend a decapsulation plan.

Talk to Watson's FA Engineering Team →

References

  • Shea, P. (Ed.). Microelectronics Failure Analysis Desk Reference, 7th ed. ASM International, 2019.
  • MIL-STD-883, Test Method Standard for Microcircuits, Method 2010 (Internal Visual, Monolithic). U.S. Department of Defense.
  • MIL-STD-1580, Destructive Physical Analysis for EEE Parts. U.S. Department of Defense.
  • SAE AS6171/4, Techniques for Suspect/Counterfeit EEE Parts Detection by Delid/Decapsulation Physical Analysis Test Methods. SAE International.
  • JEDEC JESD22-B101, External Visual. JEDEC Solid State Technology Association.